The Role and Importance of Electrical Discharge Machining in the Field of Machining
Knowledge

The Role and Importance of Electrical Discharge Machining in the Field of Machining

The principle of electrical discharge machining is simply a thermal processing method that converts electrical energy into heat energy of the work piece to quickly melt the work piece.
Published: Jun 26, 2023
The Role and Importance of Electrical Discharge Machining in the Field of Machining

Definition of Electrical Discharge Machining

Electrical Discharge Machining (EDM) is a manufacturing process that generates sparks by discharge to make the workpiece into the desired shape. The dielectric liquid separates the two electrodes and applies a voltage to produce a rapidly and periodically changing current discharge to process the material. One of the electrodes is called a tool electrode, or pole head, and the other electrode is called a workpiece electrode, or simply a workpiece. In the process of electrical discharge machining, there will be no actual contact between the tool electrode and the workpiece electrode.

When the potential difference between the two electrodes increases, the electric field between the two electrodes also increases until the electric field strength is higher than the dielectric strength. At this time, dielectric breakdown occurs, and current flows through the two electrodes. This phenomenon is the same as the capacitor collapse, removing part of the electrode material. When the current stops, the new dielectric will flow into the electric field between the electrodes, excluding solid particles, and the insulation of the dielectric is restored. After the current flows, the potential difference between the two electrodes will return to before the dielectric breakdown, so that a new dielectric breakdown can be repeated.

Machining Process

Electric discharge machining is commonly used in mold processing: EDM and wire cutting. The electrical discharge machining referred to here mainly refers to wire cutting, although the same is an electrical discharge, the efficiency is very different.

The working principle of electrical discharge machining is: between the machine tool and the workpiece (positive and negative electrodes), a method of machining to remove excess material by electrical corrosion during electrical discharge to achieve the size and shape quality of the remaining workpiece. Take discharge as an example:

电极:The electrode selection material needs good conductivity, high melting point, easy processing, and corrosion-resistant materials. Common materials are copper, graphite, copper-tungsten alloy, and molybdenum. Copper and molybdenum wire are the main wire cutting materials. When processing, the electrode and the product will be corroded at the same time, but because of the characteristics of the electrode, the degree of corrosion is much smaller than the amount of erosion of the workpiece, which can be almost ignored.

Liquid Coolant:The main function of the liquid coolant is not cooling, but as a discharge medium, which plays a role in cooling and chip removal during processing. The requirements are low viscosity, high melting point, and relatively stable, non-volatile materials, common are: kerosene, deionized water, and emulsion.

After the pulse voltage is applied between the machine tool electrode and the workpiece, once there is a proper gap between the workpiece and the electrode, the current will break the medium between the workpiece and the electrode, and a connected discharge channel appears.
放电通道将立即生成高temperatures, causing the surface of the workpiece to melt or even vaporize. It rapidly shrinks and explodes at the discharge gap. A small part of the surface of the workpiece is eroded and thrown out, and a huge electrical pit appears.
After the completion of one electrical discharge machining, the two electrodes will quickly return to a safe distance, relying on the dielectric to restore insulation. In this way, the surface of the workpiece is gradually eroded by the pulse voltage repeatedly acting on the workpiece and the electrode, but this process is very slow.

Electric Discharge Machine

Electrical Discharge Machine(EDM), Die-sinking EDM, also called cavity type EDM or volume EDM consists of an electrode and workpiece submerged in an insulating liquid such as more typically, oil or, less frequently, other dielectric fluids. The electrode and workpiece are connected to a suitable power supply. The power supply generates an electrical potential between the two parts. As the electrode approaches the workpiece, dielectric breakdown occurs in the fluid, forming a plasma channel, and a small spark jumps.
These sparks usually strike one at a time because it is improbable that different locations in the inter-electrode space have identical local electrical characteristics which would enable a spark to occur simultaneously in all such locations. These sparks happen in huge numbers at seemingly random locations between the electrode and the workpiece. As the base metal is eroded, and the spark gap subsequently increased, the electrode is lowered automatically by the machine so that the process can continue uninterrupted. Several hundred thousand sparks occur per second, with the actual duty cycle carefully controlled by the setup parameters. These controlling cycles are sometimes known as "on time" and "off-time." The on-time setting determines the length or duration of the spark. Hence, a longer on time produces a deeper cavity for that spark and all subsequent sparks for that cycle, creating a rougher finish on the workpiece. The reverse is true for a shorter time. Off time is the period of time that one spark is replaced by another. A longer off time, for example, allows the flushing of dielectric fluid through a nozzle to clean out the eroded debris, thereby avoiding a short circuit. These settings can be maintained in microseconds. The typical part geometry is a complex 3D shape, often with small or odd-shaped angles. Vertical, orbital, vectorial, directional, helical, conical, rotational, spin, and indexing machining cycles are also used.

Some of the advantages of EDM include machining of:

  1. Complex shapes that would otherwise be difficult to produce with conventional cutting tools.
  2. Extremely hard material to very close tolerances.
  3. Very small workpieces where conventional cutting tools may damage the part from excess cutting tool pressure.
  4. There is no direct contact between tool and workpiece. Therefore delicate sections and weak materials can be machined without any distortion.
  5. A good surface finish can be obtained.
  6. Very fine holes can be drilled.

Some of the disadvantages of EDM include:

  1. The slow rate of material removal.
  2. Potential fire hazard associated with use of combustible oil-based dielectrics.
  3. The additional time and cost used for creating electrodes for ram/sinker EDM.
  4. Specific power consumption is very high.
  5. 鲍威r consumption is high.
  6. Electrically non-conductive materials can be machined only with specific set-up of the process.
Published by Jun 26, 2023 Source :wikipediaSource :kknewsSource :yawjet

Further reading

You might also be interested in ...

Headline
Knowledge
Metal Cutting Machine Tool Selection for Hardware Components and Manufacturing Processes
In the cutting of hardware components, a comprehensive analysis of factors is required, and through strict process flow, a suitable cutting process can be planned to manufacture hardware components of stable quality.
Headline
Knowledge
Understanding Predictive Maintenance and Preventive Maintenance
What are the predictive maintenance and preventive maintenance? Predictive and preventive maintenances often include condition monitoring hardware, industrial automation hardware, communication connections, storage and platforms, and data analysis.
Headline
Knowledge
Understanding Electric Linear Actuators
With the continuous development of the downstream industry of linear actuator and the continuous expansion of linear actuator applications, the global demand for linear actuator has shown a rapid growth. In 2019, the global linear actuator market has exceeded 15 billion yuan.
Headline
Knowledge
An Insight Into Operations and Trends to the Warehousing and Transportation Industry
With the soaring volume of e-commerce transactions, the demand for logistics is also rising. In the process of industry transformation and upgrading, smart technology has become one of the keys to industry development.
Headline
Knowledge
Introducing Five Types of Stamping Processes: Milling, Machining, Die-Casting, Investment Casting, and Forging
Stamping is a metal shaping process that involves the use of punches and dies to shape thin-walled metal parts.
Headline
Knowledge
Five Key Directions to Explore the Radial Drilling Machine
It is a metal cutting processing equipment. The rocker arm can be rotated and lifted around the column. The spindle box is a horizontally-moving drilling machine on the rocker arm.
Headline
Knowledge
Exploring Sheet Metal: Definition, Applications, and Laser Implementation
The word comes from the English called plate metal. Generally, some metal sheets are plastically deformed by hand or die-stamping to form the desired shape and size and can be further formed by welding or a small amount of mechanical processing to form more complex parts.
Headline
Knowledge
Unraveling the Concepts of Predictive Maintenance and Preventive Maintenance
What is a predictive maintenance strategy? In short, it uses the algorithm to analyze and detect the mechanical state before the failure, and predict the time when the failure occurs. In addition to this, it is also possible to determine the type of proactive tasks that can prolong the service life of the machine.
Headline
Knowledge
Delving into the Core of Flexible Manufacturing
Flexible production refers to relying on highly flexible manufacturing equipment mainly based on computer numerical control machine tools to realize multi-variety and small-batch production methods. Committed to the goal of zero switching costs, and reduce this waste as much as possible; then the capacity can be adjusted to make it consistent with the market demand capacity.
Headline
Knowledge
研磨机的概述:介绍Guide to Daily Maintenance Procedures
磨床或磨床是一种工业战俘er tool that uses an abrasive wheel for cutting. There are various grinding machine types, each with a different purpose.
Headline
Knowledge
Exploring A Planing Machine
A shaper is a type of machine tool that uses the linear relative motion between the workpiece and a single-point cutting tool to machine a linear toolpath. Its cut is analogous to that of a lathe, except that it is (archetypally) linear instead of helical.
Headline
Knowledge
Choosing the Optimal Milling Cutter and Method
When selecting a milling cutter suitable for the machining task, various issues such as the geometry, size, and work piece material of the parts to be processed must be considered.
Agree